E-flite UMX Habu S DF180m BNF Manual de instrucciones descargar pdf (Pagina 4)

SAFE

™

Transmitter Setup

Your DSM2/DSMX transmitter will need to be conﬁ gured using the provide transmitter setup chart in order

to experience all the features and beneﬁ ts of the receiver with SAFE

™

in this aircraft.

Quick Overview

• SAFE Flight mode is selected using Channel 5 signal (high, middle, low).

• Panic mode is selected with Channel 6 signal (high, low). Refer to your transmitter’s manual for detailed

information on how to navigate through your transmitter settings.

IMPORTANT: A transmitter with a 2-position channel 5 switch will only allow the use of position 0 or

position 2 ﬂ ight modes.

Computerized Transmitter Setup (DX6i, DX6, DX7S, DX8, DX9, DX10t and DX18)

Start all transmitter programming with a blank ACRO model (do a model reset), then name the model.

Set Dual Rates to: HIGH 100% LOW 70%

Set Servo Travel to: 100%

DX6i

1. Go to the SETUP LIST MENU

2. Set MODEL TYPE: ACRO

3. Set REVERSE: Gear Channel

4. Go to ADJUST LIST MENU

5. Set TRAVEL ADJ: Gear/Fmode (0) 100%, Gear/Fmode (1) 40%

6. Set FLAPS: Norm 100, LAND 100

7. Set MIX 1: ACT; Gear Gear ACT, RATE D 0%; U + 100%, SW MIX, TRIM INH

Resulting in:

The Gear and Mix switches operate the 3 SAFE modes.

Gear 0; Mix 0 = Beginner Mode

Gear 1; Mix 0 = Intermediate Mode

Gear 1; Mix 1 = Experienced Mode

The Flap switch operates Panic Recovery: Position 0=Off

Position 1=On. (not a momentary switch)

DX7S

DX8

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set SWITCH SELECT: Change all to INH: Then TRAINER: AUX1

Then FLAP: GEAR

4. Go to the FUNCTION LIST

5. Set SERVO SETUP: Reverse AUX1

Resulting in:

Flap/Gyro Switch operates the 3 SAFE modes.

0 = Beginner Mode

1 = Intermediate Mode

2 = Experienced Mode

The Trainer/Bind button operates Panic Recovery

DX6

DX9

DX10t

DX18

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set WING TYPE: NORMAL

4. Go to CHANNEL ASSIGN: Channel Input Conﬁ g:

Set GEAR: D (DX10t: GEAR: A)

Set AUX1: I (DX10t: AUX1: R-TIP)

5. Go to the FUNCTION LIST

6. Set SERVO SETUP: Reverse AUX1

Resulting in:

Switch D (DX10t: A) operates the 3 SAFE modes.

0 = Beginner Mode

1 = Intermediate Mode

2 = Experienced Mode

The Bind/I button (DX10t: R-TIP) operates Panic Recovery

IMPORTANT: After you set up your model, always rebind the transmitter and receiver to set the desired

failsafe positions.

1 2 3 4 5 6 7 8 9 ... 18 19

Comentarios a estos manuales

Sin comentarios

E-flite UMX Habu S DF180m BNF Manual de instrucciones Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Juguetes con control remoto E-flite UMX Habu S DF180m BNF